We manufacture spoke rims for almost all motorcycles - we have made a picture selection of our already made spoke rims here, which you are welcome to use for orientation. The matching wheel hubs for the rims are manufactured according to the dimensions of your original cast wheels and can thus be installed plug & play without any further modifications in the vehicle (screw on brake discs, mount tires and install). The tires are always mounted in conjunction with inner tubes. We can offer you the original sizes (as with your cast rims) or even (if there is enough space in the swingarm and chain) wider rims. Aluminum rims go up to max. 5.5", stainless steel rims up to 10.0". Information about the choice of wheel hubs: First, decide whether you need a front or rear hub in the variant selection (depending on where the rim will be installed). If you already have suitable wheel hubs, please select "supplied by customer" and send us the wheel hub safely packed by mail (RF-Biketech GmbH, Mühlweg 10, 97702 Nüdlingen, Germany). Here, we will then spoke the selected rim ring. If you do not have a suitable wheel hub, we will manufacture it ourselves. For the front wheel hubs, please measure the inner diameter of your brake discs. If this is max. 75 mm, please select "diameter up to 150 mm", if more than 75 mm, please select "over 150 mm diameter". In the case of a rear wheel hub, generally select "diameter more than 150 mm", unless the wheels are for a single-sided swingarm with central nut mount, in which case select "diameter up to 150 mm". The wheel hubs are made of high-strength aluminum. Of course, we try to make them as light as possible. Standard are 40 spoke holes, but 60 spokes are also possible. The wheel hubs are delivered including mounted wheel bearings (C3 including dust cover). TÜV information: (only Germany) TÜV reports are specific to your vehicle for the aluminum spoke rims, and strength reports as well as certificates are included for the stainless steel spoke rims. Surface treatment information: The surface of the spokes always remains polished stainless steel, but you can configure the surface of the rims and wheel hubs in the variant selection - in addition to the classics "high gloss polished" and "black matt or black gloss powder coated", it is also possible to select the surface in any RAL color (gloss or matt). For this purpose, please specify the RAL color in the comment field in the checkout (when completing the order) or simply inform us by mail (with your order number). For even more individual requests: Special custom designs are of course also possible with us - so if you have even more specific requests, just send us an email or give us a call. We will be happy to advise you and provide you with an offer in the shortest possible time.

These Dyna ignition coils are suitable for original ignition systems and all Dyna ignition systems. The small size makes them ideal for custombikes. They generate an ignition voltage of 40,000 V. Matching ignition cables available here in the store. Supplied as a set with 2 outputs each. Scope of delivery: Dyna ignition coils 3 ohms with double output (2 pieces) Connector plugs

Contactless, high quality ignition system from Dyna. Installation can be done very easily (within 30 min). Can be operated either with the original ignition coils or better with the Dyna ignition coils (also available here in the store). Advantages: No more annoying adjustment of the breaker contacts, exact ignition timing, better combustion, absolutely maintenance free. Scope of delivery: Dyna S ignition system complete Connection material

Colored Dyna silicone ignition wires with graphite shielding. Fits with our Dyna ignition coils. Can be shortened to any required length. Sufficient for almost all four cylinder models. Scope of delivery: Set of two 120 cm long cables with 4 spark plug connectors 7 mm cable cross section Mounting material

We widen the original cast wheels of your motorcycle! The advantage is that you can then drive wider or even changed in diameter wheels / tires without having to make further changes to the bike. The wheel hubs remain unchanged, only the rim beds are changed. Of course you have to take into account the clearance wheel-chain, wheel-cardan, wheel-belt and the width of the swingarm. In most cases, the original rim widening for motorcycles is also the most cost-efficient way to realize wheel size changes. For widening, the original rim beds are turned on special lathes and then machine-welded to corresponding larger rim beds using the TIG welding process. The weld is no longer visible in the outer area of the rim beds and the rim looks like a "normal" rim. A strength certificate with identification is enclosed. Note: If you are unsure whether your rim can be widened, send us a picture by mail in advance! We will be happy to advise you. Here's why: Cast rims, which have a rim bed, into which no cast spokes run from the inner star, can generally be widened (that's most rims). However, there are also rims where the cast spokes merge into the rim bed. Here, it is usually difficult or even impossible to widen the wheel. Furthermore, the following applies: A rim can be widened by a maximum of 2.0" in the same diameter, e.g. 3.5" x 17" to a maximum of 5.5" x 17". Wider is also possible, but then the diameter of the rim must be increased by 1", e.g. 5.5" x 17" to 10.0" x 18". The wheels are blasted before processing and must be resurfaced after widening, which we of course also offer - just select the desired variant (coated, painted, polished). Our variants here in the store are always based on delivered 17" or 18" wheels. Other dimensions on request by mail. Please send or deliver wheels without attachments (brake discs, tires, sprocket carrier) by mail to us. The procedure: Place your order here in the store or send us an e-mail request Send the bike to us by mail (print out the order confirmation and put it in the package) to the address RF-Biketech GmbH, Mühlweg 10, 97720 Nüdlingen, Germany We widen the wheel as desired and treat the surface depending on the variant We send the widened wheel back to you Scope of delivery: Widened wheel (wheel bearings are not mounted but attached in the package) technical report with identification (Festigkeitsgutachten) for TÜV (Germany)

Here's our inhouse CNC-machined triple clamp set type 1 (Triple clamp sizes: top 30 mm, 1 clamping, below 35 mm, 2 clampings) made from high strength aluminum. Our triple clamp types from type 1 to type 5 are universal triple clamps/fork bridges, which are individually manufactured by us according to your wishes. For even more individual inquiries, please feel free to contact us by mail or phone, we are always happy to advise you and send you an offer by mail. We manufacture triple clamps for almost all standpipe distances, clamp diameters and offsets. Also we can consider original cockpits and ignition locks as well as after sale cockpits that are integrated in the triple clamp (f.e. motoscope pro). Fork covers: It is also possible to prepare the triple clamp for fork covers. Because we have to consider additional things here, please contact us via e-mail or phone. With a fork conversion the following criteria are always to be considered: Which brake system should be used in the fork conversion? (The original brake system or the brake system matching the fork? Both are possible, but the brake system matching the fork is recommended.) Which front wheel will be used? (The original front wheel or the wheel matching the fork? The wheel matching the fork is recommended.) Clamping diameter of the fork top and bottom Fork tube distance center - center Offset (center steering tube to center fork tube) Dimension of the steering tube (best with a sketch, which you send us in addition to the order via e-mail) Dimension of the steering stops (best with a sketch, which you send us in addition to the order via e-mail) If you are technically proficient enough to measure the desired triple clamp yourself, then please download the following form and send it to us filled out by e-mail with your order number from the store (if you have configured and ordered something here) to info@rf-biketech.de. You then select "Production via sketch" in the variants. We add the missing dimensions (f.e. the heights of the triple clamps etc.) ourselves when we manufacture the triple clamp. Download Form If you do not have the detailed measurements or are unsure, you can alternatively send the parts to us and we measure them ourselves. In that case, please select "Sample via mail" in the variants. For the sample package we need the following parts from you: lower original triple clamp of the bike lower triple clamp of the new fork upper original triple clamp (only if original steering lock and original cockpit are reinstalled) Of course you will get the parts back intact. They serve exclusively for the measurement. These measurements are so important, because during the production of your desired triple clamp the distance measurements can be taken into account (fork tube distance to each other), so that later the wheel and the brake system can be installed without further adapters. The steering stops or speedometer holders on the respective pictures here will of course look different on your triple clamp than on our sample pictures. Scope of delivery: Ready-to-install triple clamp set with pressed-in steering tube (stainless steel) Triple clamp sizes: top 30 mm, 1 clamping, below 35 mm, 2 clampings TÜV certificate (technical report)

Here's our inhouse CNC-machined triple clamp set type 2 (Triple clamp sizes: top 40 mm, 2 clamping, below 60 mm, 3 clampings) made from high strength aluminum. Our triple clamp types from type 1 to type 6 are universal triple clamps/fork bridges, which are individually manufactured by us according to your wishes. For even more individual inquiries, please feel free to contact us by mail or phone, we are always happy to advise you and send you an offer by mail. We manufacture triple clamps for almost all standpipe distances, clamp diameters and offsets. Also we can consider original cockpits and ignition locks as well as after sale cockpits that are integrated in the triple clamp (f.e. motoscope pro). Fork covers: It is also possible to prepare the triple clamp for fork covers. Because we have to consider additional things here, please contact us via e-mail or phone. With a fork conversion the following criteria are always to be considered: Which brake system should be used in the fork conversion? (The original brake system or the brake system matching the fork? Both are possible, but the brake system matching the fork is recommended.) Which front wheel will be used? (The original front wheel or the wheel matching the fork? The wheel matching the fork is recommended.) Clamping diameter of the fork top and bottom Fork tube distance center - center Offset (center steering tube to center fork tube) Dimension of the steering tube (best with a sketch, which you send us in addition to the order via e-mail) Dimension of the steering stops (best with a sketch, which you send us in addition to the order via e-mail) If you are technically proficient enough to measure the desired triple clamp yourself, then please download the following form and send it to us filled out by e-mail with your order number from the store (if you have configured and ordered something here) to info@rf-biketech.de. You then select "Production via sketch" in the variants. We add the missing dimensions (f.e. the heights of the triple clamps etc.) ourselves when we manufacture the triple clamp. Download Form If you do not have the detailed measurements or are unsure, you can alternatively send the parts to us and we measure them ourselves. In that case, please select "Sample via mail" in the variants. For the sample package we need the following parts from you: lower original triple clamp of the bike lower triple clamp of the new fork upper original triple clamp (only if original steering lock and original cockpit are reinstalled) Of course you will get the parts back intact. They serve exclusively for the measurement. These measurements are so important, because during the production of your desired triple clamp the distance measurements can be taken into account (fork tube distance to each other), so that later the wheel and the brake system can be installed without further adapters. The steering stops or speedometer holders on the respective pictures here will of course look different on your triple clamp than on our sample pictures. Scope of delivery: Ready-to-install triple clamp set with pressed-in steering tube (stainless steel) Triple clamp sizes: top 40 mm, 2 clamping, below 60 mm, 3 clampings TÜV certificate (technical report)

Here's our inhouse CNC-machined triple clamp set type 3 (Triple clamp sizes: top 70- 80 mm, 4 clamping, below 80 mm, 4 clampings) made from high strength aluminum. Our triple clamp types from type 1 to type 6 are universal triple clamps/fork bridges, which are individually manufactured by us according to your wishes. For even more individual inquiries, please feel free to contact us by mail or phone, we are always happy to advise you and send you an offer by mail. We manufacture triple clamps for almost all standpipe distances, clamp diameters and offsets. Also we can consider original cockpits and ignition locks as well as after sale cockpits that are integrated in the triple clamp (f.e. motoscope pro). Fork covers: It is also possible to prepare the triple clamp for fork covers. Because we have to consider additional things here, please contact us via e-mail or phone. With a fork conversion the following criteria are always to be considered: Which brake system should be used in the fork conversion? (The original brake system or the brake system matching the fork? Both are possible, but the brake system matching the fork is recommended.) Which front wheel will be used? (The original front wheel or the wheel matching the fork? The wheel matching the fork is recommended.) Clamping diameter of the fork top and bottom Fork tube distance center - center Offset (center steering tube to center fork tube) Dimension of the steering tube (best with a sketch, which you send us in addition to the order via e-mail) Dimension of the steering stops (best with a sketch, which you send us in addition to the order via e-mail) If you are technically proficient enough to measure the desired triple clamp yourself, then please download the following form and send it to us filled out by e-mail with your order number from the store (if you have configured and ordered something here) to info@rf-biketech.de. You then select "Production via sketch" in the variants. We add the missing dimensions (f.e. the heights of the triple clamps etc.) ourselves when we manufacture the triple clamp. Download Form If you do not have the detailed measurements or are unsure, you can alternatively send the parts to us and we measure them ourselves. In that case, please select "Sample via mail" in the variants. For the sample package we need the following parts from you: lower original triple clamp of the bike lower triple clamp of the new fork upper original triple clamp (only if original steering lock and original cockpit are reinstalled) Of course you will get the parts back intact. They serve exclusively for the measurement. These measurements are so important, because during the production of your desired triple clamp the distance measurements can be taken into account (fork tube distance to each other), so that later the wheel and the brake system can be installed without further adapters. The steering stops or speedometer holders on the respective pictures here will of course look different on your triple clamp than on our sample pictures. Scope of delivery: Ready-to-install triple clamp set with pressed-in steering tube (stainless steel) Triple clamp sizes: top 70- 80 mm, 4 clamping, below 80 mm, 4 clampings TÜV certificate (technical report)

Here's our inhouse CNC-machined triple clamp set type 4 (Triple clamp sizes: top 80 mm, 4 clampings, below 100 mm, 5 clampings) made from high strength aluminum. Our triple clamp types from type 1 to type 6 are universal triple clamps/fork bridges, which are individually manufactured by us according to your wishes. For even more individual inquiries, please feel free to contact us by mail or phone, we are always happy to advise you and send you an offer by mail. We manufacture triple clamps for almost all standpipe distances, clamp diameters and offsets. Also we can consider original cockpits and ignition locks as well as after sale cockpits that are integrated in the triple clamp (f.e. motoscope pro). Fork covers: It is also possible to prepare the triple clamp for fork covers. Because we have to consider additional things here, please contact us via e-mail or phone. With a fork conversion the following criteria are always to be considered: Which brake system should be used in the fork conversion? (The original brake system or the brake system matching the fork? Both are possible, but the brake system matching the fork is recommended.) Which front wheel will be used? (The original front wheel or the wheel matching the fork? The wheel matching the fork is recommended.) Clamping diameter of the fork top and bottom Fork tube distance center - center Offset (center steering tube to center fork tube) Dimension of the steering tube (best with a sketch, which you send us in addition to the order via e-mail) Dimension of the steering stops (best with a sketch, which you send us in addition to the order via e-mail) If you are technically proficient enough to measure the desired triple clamp yourself, then please download the following form and send it to us filled out by e-mail with your order number from the store (if you have configured and ordered something here) to info@rf-biketech.de. You then select "Production via sketch" in the variants. We add the missing dimensions (f.e. the heights of the triple clamps etc.) ourselves when we manufacture the triple clamp. Download Form If you do not have the detailed measurements or are unsure, you can alternatively send the parts to us and we measure them ourselves. In that case, please select "Sample via mail" in the variants. For the sample package we need the following parts from you: lower original triple clamp of the bike lower triple clamp of the new fork upper original triple clamp (only if original steering lock and original cockpit are reinstalled) Of course you will get the parts back intact. They serve exclusively for the measurement. These measurements are so important, because during the production of your desired triple clamp the distance measurements can be taken into account (fork tube distance to each other), so that later the wheel and the brake system can be installed without further adapters. The steering stops or speedometer holders on the respective pictures here will of course look different on your triple clamp than on our sample pictures. Scope of delivery: Ready-to-install triple clamp set with pressed-in steering tube (stainless steel) Triple clamp sizes: top 80 mm, 4 clampings, below 100 mm, 5 clampings TÜV certificate (technical report)

Here's our inhouse CNC-machined triple clamp set type 5 (Triple clamp sizes: top and below 30-35 mm, 2 clampings) made from high strength aluminum. Our triple clamp types from type 1 to type 6 are universal triple clamps/fork bridges, which are individually manufactured by us according to your wishes. For even more individual inquiries, please feel free to contact us by mail or phone, we are always happy to advise you and send you an offer by mail. We manufacture triple clamps for almost all standpipe distances, clamp diameters and offsets. Also we can consider original cockpits and ignition locks as well as after sale cockpits that are integrated in the triple clamp (f.e. motoscope pro). Fork covers: It is also possible to prepare the triple clamp for fork covers. Because we have to consider additional things here, please contact us via e-mail or phone. The type 5 triple clamp was developed primarily for length compensation for forks that are too short. The cranking (30 or 35 mm) lengthens the fork and more ground clearance is achieved. This also affects the trail accordingly. With a fork conversion the following criteria are always to be considered: Which brake system should be used in the fork conversion? (The original brake system or the brake system matching the fork? Both are possible, but the brake system matching the fork is recommended.) Which front wheel will be used? (The original front wheel or the wheel matching the fork? The wheel matching the fork is recommended.) Clamping diameter of the fork top and bottom Fork tube distance center - center Offset (center steering tube to center fork tube) Dimension of the steering tube (best with a sketch, which you send us in addition to the order via e-mail) Dimension of the steering stops (best with a sketch, which you send us in addition to the order via e-mail) If you are technically proficient enough to measure the desired triple clamp yourself, then please download the following form and send it to us filled out by e-mail with your order number from the store (if you have configured and ordered something here) to info@rf-biketech.de. You then select "Production via sketch" in the variants. We add the missing dimensions (f.e. the heights of the triple clamps etc.) ourselves when we manufacture the triple clamp. Download Form If you do not have the detailed measurements or are unsure, you can alternatively send the parts to us and we measure them ourselves. In that case, please select "Sample via mail" in the variants. For the sample package we need the following parts from you: lower original triple clamp of the bike lower triple clamp of the new fork upper original triple clamp (only if original steering lock and original cockpit are reinstalled) Of course you will get the parts back intact. They serve exclusively for the measurement. These measurements are so important, because during the production of your desired triple clamp the distance measurements can be taken into account (fork tube distance to each other), so that later the wheel and the brake system can be installed without further adapters. The steering stops or speedometer holders on the respective pictures here will of course look different on your triple clamp than on our sample pictures. Scope of delivery: Ready-to-install triple clamp set with pressed-in steering tube (stainless steel) Triple clamp sizes: top and below 30-35 mm, 2 clampings TÜV certificate (technical report)

Here's our inhouse CNC-machined triple clamp set type 6 (Triple clamp sizes: top 40 mm, 2 clamping, below 60 mm, 3 clampings) made from high strength aluminum. Our triple clamp types from type 1 to type 6 are universal triple clamps/fork bridges, which are individually manufactured by us according to your wishes. For even more individual inquiries, please feel free to contact us by mail or phone, we are always happy to advise you and send you an offer by mail. We manufacture triple clamps for almost all standpipe distances, clamp diameters and offsets. Also we can consider original cockpits and ignition locks as well as after sale cockpits that are integrated in the triple clamp (f.e. motoscope pro). Fork covers: It is also possible to prepare the triple clamp for fork covers. Because we have to consider additional things here, please contact us via e-mail or phone. With a fork conversion the following criteria are always to be considered: Which brake system should be used in the fork conversion? (The original brake system or the brake system matching the fork? Both are possible, but the brake system matching the fork is recommended.) Which front wheel will be used? (The original front wheel or the wheel matching the fork? The wheel matching the fork is recommended.) Clamping diameter of the fork top and bottom Fork tube distance center - center Offset (center steering tube to center fork tube) Dimension of the steering tube (best with a sketch, which you send us in addition to the order via e-mail) Dimension of the steering stops (best with a sketch, which you send us in addition to the order via e-mail) If you are technically proficient enough to measure the desired triple clamp yourself, then please download the following form and send it to us filled out by e-mail with your order number from the store (if you have configured and ordered something here) to info@rf-biketech.de. You then select "Production via sketch" in the variants. We add the missing dimensions (f.e. the heights of the triple clamps etc.) ourselves when we manufacture the triple clamp. Download Form If you do not have the detailed measurements or are unsure, you can alternatively send the parts to us and we measure them ourselves. In that case, please select "Sample via mail" in the variants. For the sample package we need the following parts from you: lower original triple clamp of the bike lower triple clamp of the new fork upper original triple clamp (only if original steering lock and original cockpit are reinstalled) Of course you will get the parts back intact. They serve exclusively for the measurement. These measurements are so important, because during the production of your desired triple clamp the distance measurements can be taken into account (fork tube distance to each other), so that later the wheel and the brake system can be installed without further adapters. The steering stops or speedometer holders on the respective pictures here will of course look different on your triple clamp than on our sample pictures. Scope of delivery: Ready-to-install triple clamp set with pressed-in steering tube (stainless steel) Triple clamp sizes: top 40 mm, 2 clamping, below 60 mm, 3 clampings TÜV certificate (technical report)