CNC-milled footrest system from our own company for Kawasaki Z 650/750, Kawasaki Z 900/1000/Z1R/MK2 and Kawasaki Z 1000 ST models. The foot rest system is made of high-strength aluminum and is plug & play mountable. The system is set back approx. 30 mm. The original brake cylinder of the old Z models no longer fits - we use a brake cylinder from newer Kawasaki models, e.g. ZX6R, ZRX7R, ZRX9R from 1995 to 2003.
The system also fits all Z 1 / Z 900 models, but these must then be converted to rear disc brakes (original drum brakes).
Scope of delivery:
Pre-assembled footrest system right and left
Shift rod with mounting for shift shaft
Brake light switch as banjo bolt
4x M10 x 1.25 retaining bolts with spacers
TÜV documents: material specifiction, sample report of identical vehicle for TÜV-Einzelabnahme. (for Germany) If there are problems with the TÜV-entry, we guarantee it at our workshop.
Contactless, high quality ignition system from Dyna. Installation can be done very easily (within 30 min). Can be operated either with the original ignition coils or better with the Dyna ignition coils (also available here in the store).
Advantages: No more annoying adjustment of the breaker contacts, exact ignition timing, better combustion, absolutely maintenance free.
Scope of delivery:
Dyna S ignition system complete
Connection material
K&N single air filters (set of 4), suitable for all Mikuni RS 34 and Mikuni RS 36 carburetors and for Z 1000/J/R carburetors. Highly recommended with Mikuni flat slide carburetor conversions.
Info TÜV: TÜV-Einzelabnahme required! (In Germany) The TÜV entry is also possible in our house.
Scope of delivery:
K&N single air filter (4 pieces)
VA Clamps
Original handlebar switch for the old Z-models as a replica part. Fits for original wiring Z 1 900 and Z 900 A4. Also usable for original wiring Z 1000 A1 and A2, however the compact plug has to be replaced with single plugs. We offer the switches as a set as well as right or left side only.
Scope of delivery:
Handlebar switch, wired (as shown on the pictures)
choose between set, right or left side
New ignition lock for Z 1 900, Z 900 A4 as well as Z 1000 A1/A2. Replica-part. The 4-pin plug fits with the 6-pin counterpart plug of the wiring harness (if your wiring harness is equipped this way).
Scope of delivery:
Ignition lock with 2 keys and holding plate
Aluminum exhaust pipe holders/crowns for all old Z and GPZ models. We also offer fitting exhaust pipe collars for each exhaust system (also in the store).
Attention: Price for one piece (not 4 pieces as seen in the picture).
Scope of delivery:
Exhaust pipe holder, aluminum, 1 piece
Original spare part from Kawasaki, Cam chain tensioner-assy with rubber wheel for Z 1 900, Z 900 A4, Z 1000 A1 und A2, Z 1000 MK2, Z 1 R and Z 1000 ST.
Scope of delivery:
Cam chain tensioner-assy with rubber wheel, 1 piece
Cranked chain sprocket for our wide wheel conversion to 180/190 tires for Z 1 900, Z 900 A4, Z 1000 A1 and A2, Z 1 R and Z 1000 MK2 engines. In most cases, an 14 mm adapter ring has to be added below the chain sprocket at the rear wheel.
Note: Sprocket for 530 chain.
Chain sprocket 530, 16/17/18 teeth (choose variant above), 14 mm cranked
Fully chromed 4 in 4 exhaust system for Z 1 900, Z 900A4 and Z 1000A. The system is no longer produced by Kawasaki, but it is reproduced using original Kawasaki tools and is, in our opinion, of even higher quality than the original.
The exhaust system is otherwise absolutely identical, the only thing missing is the factory stamp from Kawasaki (but this is not a problem for the TÜV either) - so it fully complies with the STVZO (Germany).
You will need the original parts for installation, which should be available on your original Z. If not available, the following products are available here in the store:
8x exhaust crescents
Manifold crowns
4 in 4 mounting kit
For mounting on Z 1000 models, you will also need 2 support struts that are attached to the pillion footrests, which are also available here in the store.
Scope of delivery:
4 in 4 exhaust system, chrome-plated
Colored Dyna silicone ignition wires with graphite shielding. Fits with our Dyna ignition coils. Can be shortened to any required length. Sufficient for almost all four cylinder models.
Scope of delivery:
Set of two 120 cm long cables with 4 spark plug connectors
7 mm cable cross section
Mounting material
Vehicle type:
Z 900/Z 1000/MK2/Z1R/GPZ 1100B1/B2/UT
Mikuni RS 36 carburetor for Zephyr 1100 or for Z 900, Z 1000, Z 1000 MK2, Z1R, GPZ 1100 B1, GPZ 1100 B2 and GPZ 1100 UT – please choose your vehicle in the variants above! This carburetor can be installed in conjunction with the original air filter box and the original intake rubbers, only the original throttle cable must be slightly modified. This RS 34 Mikuni flat slide carburetor can be installed in conjunction with the original air filter box and the original intake rubbers, only the original throttle cable must be slightly modified. You can expect more power and higher torque due to the optimal tunability. For this purpose, the K&N exchange filter is highly recommended.
The RS carburetor kits from Mikuni are available for a variety of different motorcycles. These carburetors have proven themselves very well over the years, both on racing and street bikes. The advantages of these carburetors over stock carburetors are more spontaneous throttle response and higher power output. The more spontaneous throttle response results from the throttle slide being actuated directly by the throttle cable, in contrast to the constant-pressure carburetors, which are fitted exclusively as original equipment, where the throttle slide is lifted by a membrane with a delay. The higher power output is due on the one hand to the larger cross-section and on the other to the very good flow conditions in the RS carburetor. Important components such as the main jet, needle jet and jet needle can be replaced or modified in just a few minutes without having to remove the carburetor. The infinitely adjustable accelerator pump allows individual adjustment for different driving styles.
Scope of delivery
Complete carburetor Mikuni RS 36, ready for installation
Double rear light made of GRP, paintable. Fits in almost all RF-Biketech rear conversion kits. The double rear light has exactly the same outer shape as the popular super bike rear light. The rear light can be installed universally on many bikes.
Scope of delivery:
GRP double rear light (black)
License plate light and brake light function
2 x holding screws
Original side cover rubber as a replica part for Z 1 900, Z 900 A4, Z 1000 A1 and A2, Z 1 R, Z 1000 MK2 and Z 1000 ST. Three rubbers are required for one side cover.
Scope of delivery:
Side cover rubber, 1 piece
Nice small brake fluid compensation container for brake- and clutch pump (also usable for rear brake pump). Is delivered with universal holding plate.
Scope of delivery:
Brake fluid compensation container, black aluminum
Holding plate universal with screws
Fully electronic cockpit in retro style suitable for all motorcycles, milled from the full aluminum. Speedometer and tachometer are electronically controlled. Day/total mileage indicator, turn signal, neutral, high beam, oil. Includes ignition switch. Fits old Z models (1972 to 1978) without further adjustment work on the triple clamp. Wiring must of course still be done. For all other motorcycles adapter plates can be manufactured - if interested just contact us. Speedometer and tachometer are illuminated in blue. Control lights are indicated by LEDs.
Scope of delivery:
Completely assembled retro cockpit incl. speedometer sensor
Cable kit
Universal ignition lock (plug fits old Z models plug & play)
TÜV-certificate
These Dyna ignition coils are suitable for original ignition systems and all Dyna ignition systems. The small size makes them ideal for custombikes. They generate an ignition voltage of 40,000 V. Matching ignition cables available here in the store. Supplied as a set with 2 outputs each.
Scope of delivery:
Dyna ignition coils 3 ohms with double output (2 pieces)
Connector plugs
Set of intake rubbers for RS 34 and RS 36 Mikuni flat slide carburetors, suitable for all Z models from Z 1 900 to GPZ 1100.
Scope of delivery:
Set of intake rubbers, 4 pieces
Original fuel tap / petcock for Z 1 900, Z 900 and Z 1000 A1/A2 as well as Z 1 R. Replica part.
Scope of delivery:
Fuel tap / petcock with union nut, 1 piece
This clutch cover for Z 900, Z 1000, Z 1000 MK2, Z 1000 ST and Z 1 R is CNC-milled from solid aluminum and is easily interchangeable with the original clutch cover. The visor made of Makrolon is very durable and is screwed into the cover - so can be easily replaced at any time if damaged.
Scope of delivery:
Clutch cover aluminum (surface depending on variant) incl. oil filler neck and oil sight glass
Original spare part from Kawasaki. Cam chain sprocket for Z 1 900, Z 900 A4, Z 1000 A1 and A2, Z 1000 MK2, Z 1000 ST and Z 1 R.
Scope of delivery:
Cam chain sprocket, 1 piece
This alternator conversion kit for Z 1 900, Z 900 A4, Z 1000 A1 and A2, Z 1 R and Z 1000 ST was developed by us and is plug & play mountable into the original alternator cover. The alternator provides a higher charging current and is extremely durable. This is a real alternative to the wear-prone original alternator rotor/winding. The kit can be mounted together with the original starter clutch.
Here you can see the data of the original alternator vs. our kit:
Original alternator
RF alternator
RPM
Current in A
Current in A
1000
0,0
1,0
1500
0,0
10,0
2000
8,0
13,5
2500
9,5
14,5
3000
11,0
15,5
4000
14,0
17,0
Scope of delivery:
Alternator rotor
Alternator stator
CNC-machined adapter for alternator stator
Exhaust/manifold pipe collars for manifold mounting, fits Z 1 900, Z 900, Z 1000 A1 and A2, Z 1 R. Can be used in conjunction with original exhaust pipe holders or the exhaust pipe holders here in the store. For complete assembly, eight pipe collars are required!
Attention, no set price! We sell from 1 piece.
Scope of delivery:
Exhaust/manifold pipe collars, 1 piece
A 12 V start relay that fits for passt for old Z-models, can also be used universally.
Scope of delivery:
Starter relay (as seen in the picture), 12 V, 1 piece